Cab Shield

SPECIFICATOINS:  184-U (8 ft. and 10 ft.)
Quality control assures top quality
Sides:  10 -gauge hi-tensile steel A607, boxed top rail,  full-length sloping rails and fully welded full depth rear corner posts.
Floor:  10-gauge hi-tensile steel A607.
Head:  Full width inverted V-horizontal head brace.  10-gauge steel construction, 24" cab protector.
Tailgate Hardware:  Heavy duty.  Upper is drop pin style, fabricated steel hinge.  Lower hook is forged steel.  Banjo eye keeps tailgate chain in position you select.
Understructure:  5" structured channel longitudinals.  3" structural channel crossmembers.  Understure gusseted and welded to body.
Standard Length:  8', 9', 10', and 11'
Standard Width:  84" inside
Standard Capacity:  2 to 3 Cubic Yards
Standard End:  6" higher than sides
**Options:  Asphalt chute, Coal Door, 13" or 18" Sides, Half or Full Cab Protector

300-U or 300-T  9 ft. and 10 ft. long

Quality control assures top quality
Sides:  10-gauge hi-tensile steel with boxed top rail and full depth rear corner posts.  6" side board gussets with full length rub rails.  Extra-strong box-type braces give better side support and greater strength.
Rub Rails:  Full length 45 degree sloping rub rails shed material in the yard, not the road.
Floor:  10-gauge hi-tensile steel floor (8 gauge one piece optional)
Head:  10 gauge hi-tensile steel.  Full width inverted V-type horizontal head brace.
Tailgate:  Double-acting offset hinge.  Fully boxed 10 gauge hi-tensile steel with boxed horizontal reinforcements and sloping lower brace.
Tailgate Offset Hardware:  Upper hinge is offset, made of heavy-duty cast steel.  Lower hood is forged steel; engages tailgate pin from top.  Banjo eye keeps tailgate chain in position you select.
Lights and Reflectors:  Combination light and reflector, recessed and protected, shock proof and rubber mounted.
Understructure:  Completely jig built with 4" structural channel crossmembers and 6" structural longitudinals.  Understructure gusseted and welded to body.  Continuous weld construction throughout.
**Optional:  6 panel tailgate, tread grip walkrod, front corner posts, horizontal bracing, 36" cab shield, and 8 gauge body.

Barn Door

Tailgate Latch

400T or 500-T  Bodies

SPECIFICATOINS:  400T and 500TR Bodies
Sides:  One piece sides with no welded seams.  10-gauge A607 grade 50 high tensile steel with boxed top rail and fully welded boxed rear corner post.  8" side board gussets with full length rub rails, and box-type side braces.
Rub Rails:  Full length 45 degree deflector panels are an integral part of sides.
Floor:  3/16"-one piece high tensile steel floor with 2" radius corners (no seams).  A572 grade 50 steel.
Front Wall:  10 gauge hi-tensile A607 grade 50 steel.  Full width integral inverted V-type horizontal bracing.
Tailgate:  9 panel.  Fully boxed 10 gauge high tensile A607 grade 50 steel with boxed horizontal reinforcements and sloping lower deflector.  Tailgate is 8" higher than sides.
Tailgate Hardware:  Heavy duty; upper is offset cast steel hinge.  Lower hook is cast steel; engages tailgate pin from top. Banjo eye keeps tailgate chain in position you select.
Lights and Reflectors: Federal 108 lights are standard, recessed for protection, rubber mounted and shock proof.
Understructure:  Completely jig built with 4" structural channel crossmembers on 12" centers and 7" structural reinforced channel longitudinal.  Crossmembers are gusseted and welded to longitudinal.
**Options:  Air tailgate latch, 36" cab shield, 8 gauge sides, 1/4" floor, sloping tailgate, air latch barn door tailgate

17'-19' Car Carriers

*All Godwin Rollbacks are fully assembled and factory tested.
Standard Features:
17', 18', and 19' models available in steel or aluminum
Payload capacity 8000 lbs. evenly distributed*
5" rollers with bronze bushings
2-3" lift cylinders - 17'
2-4" oift cylinders - 18' & 19'
3" diameter rollback cylinder
Throttle control
6" metal sides (stake pockets available on steel carrier)
1 pair of J-hooks and chains
V-chain assembly
Hydraulic tow hitch with chains|
Fluid reservoir with return filter
Ramsey 8000 lb. planetary winch
50' cable (3/8" diameter with roll cable guide)
Full length subframe (bolt on)
Front and rear tie-downs
Standard dual rear mounted control panel (illuminated)
Locking toolbox with key
All components for installation.
Federal standard 108 lighting
Patented lock down system
One year limited warranty
Fully shielded hydraulic hoses in winch track
Fully enclosed tail lights
Optional independent wheel lift.
*not based on vehicle GVWR

Understructure

Standard Features:  22', 24', and 26' Rollback Carriers
Tilt and roll capacity:  18 tons
Reservoir with return filter:  30 gallons
Loading angle (approximately):  12 degrees
Direct mount pump
Rollers with bronze bushings:  6"
Dual-illuminated controls
Throttle control
Tie downs, front and rear
Ramsey 8,000 lb. planetary winch
4" cross sills on 12" centers
Headboard:  48"
3/16 floor space
Federal I08 lights
Subframe:  Full length
Toolbox with key:  18"x18"x48"
Rear stabilizer:  Independent hydraulic
Stabilizer cylinders:  (2) 4"
Lift cylinders:  (2) 5"
Rollback cylinder:  4"

Platform 10' - 24' Long

SPECIFICATIONS:
Width:  8' overall
Crossmembers:  10' - 13' body; 3" structural channel on 12" centers.  14"- 24" body; 4" structural channel on 12" centers.
Longitudinals:  10' - 13' platform; 6" structural channel.  14' - 24' platform; 7" structural channel.
Floor:  3/16" smooth plate, one piece, A572 GD 50, up to 20'.  Optional 3/16" tread plate multiple pieces.
Rub rail:  3/8" x 2 1/2" flat bar (outside pocket bed)
Side rail:  10 GA formed sheet (outside pocket bed)
Pockets:  2" x 4 1/4" ID 3/16" material (outside pocket bed).  1 5/8" x 3 5/8" ID 3/16" material inside pocket bed
Head Boards:  42", 48", 50", and 54" flush back 10 GA A572 GD 50
Cap Protector:  24" and 36" 10 GAA572 GD 50

 ACCESSORIES:
-Flatbed with removable metal sides and barn door
-Outside pocket flatbed with removable metal slatted sides
-Half and half headboard
-Inside pocket body with 48" plywood grain sides and
swinging tailgate with grain door
-Flatbed, permanent sides, with double-acting tailgate and
cab shield with optional window
-24" permanent metal sides, headboard with optional
window and cab shield
-Standard trailer hitch (10,000 lb. capacity)
-ICC rear bumper
-Combo hitch (10,000 lb. capacity)
-Federal I08 lighting

 Additional Information:
10' - 13' Platforms:  6" structural channel longitudinals and 3" structural channel crossmembers with 12" centers
14' - 24' Platforms:  7" structural channel longitudinals and 4" structural channel crossmembers with 12" centers
Outside pocket smooth floor:  3/16" one piece floor up to 20'.  One seam on platforms over 20'
Optional diamond tread floor:  3/16" multiple piece seamed in 4' increments
Inside pocked smooth floor:  3/16" one piece floor up to 20'.  One seam on bodies over 20'

816SF and 820SF Underbody Hoists

SPECIFICATOINS:  816SF Underbody Hoist
All Godwin Hoists are NTEA rated
Direct mount pump
8.5 gallon reservoir
One 8" double or single acting cylinders with a 16" stroke
For 9' and 10' body lengths and 72" to 84" C.A.
50 degree (+/-) dumping angle
14" mounting height
Approximate weight complete 900 lbs.
Designed for single axle trucks

SPECIFICATOINS:  820SF Underbody Hoist
All Godwin Hoists are NTEA rated
Direct mount pump
8.5 gallon reservoir
One 8" single acting cylinders with a 20" stroke
For 9' and 10' body lengths and 72" to 84" C.A.
50 degree (+/-) dumping angle
14" standard mounting height
Approximate weight complete 1000 lbs.
Designed for single axle trucks

5530DM Underbody Hoist

SPECIFICATOINS:  5530DM Underbody Hoist
All Godwin Hoists are NTEA rated
The 5530DM is NTEA rated class E
Direct mount pump
8.5 gallon reservoir
Two 5" single acting cylinders with a 30" stroke
For use with Godwin 12' - 14' flatbed with 84" - 102" C.A.
45 degree dumping angle
3/4" standard mounting height
Approximate weight complete 752 lbs.
Designed for single axle trucks

Scissor Hoist

Offering 8 models of low mount truck hoists, designed for today's trucks with 31.5" to 34.5" frame and a wide range of CA's and GVWR's

Godwin Manufacturing offers welded cylinders with heavy duty chrome shafts which makes them durable and trouble-free.  They are also double acting, powering up and powering down on most models.  Being low profile, no crossmember cutting is needed.  Fast, easy installation at a lower cost is another plus. The wide, heavy design offers more stability than most other designs.